MCR Safety Carbon Fiber

NFPA 2112 Standard

NFPA 2112 Standard

Standard on Flame-Resistant Flash Fire Protection for MCR Safety FR Gear.
Please carefully review the important information before wearing MCR Safety FR Gear. Our FR Gear meets the requirements for NFPA 2112 standard on Flame-Resistant Clothing for Protection of Industrial Personnel Against Short-Duration Thermal Exposures from Fire.

PRE-USE INFORMATION

  • Safety Considerations:

    For prevention of clothing ignition during short term and emergency exposure to flame.

  • Limitations of Use:

    Flame-Resistant (FR) Garments: Do not use for protection against continuous thermal loads, hot liquids or steam. Do not wear alone for limb/torso protection during structural firefighting. Do not use for chemical protection. Failure to comply with this warning may result in serious injury or death.

  • Marking Recommendations and Restrictions

    If the end user adds any lettering, trim, emblems, or name tags, etc. to the garment, they must meet the performance requirements of the standard. Do not mark, remove, or write over existing labels. Failure to comply will invalidate the Company warranty.

  • Warranty Information

    Company guarantees that all garments will be free of workmanship defects resulting from normal wear within one year of the purchase for garments laundered per our instructions. Apparel color shifting or fading is excluded. Shelby MCR Safety Uniform will determine whether a returned garment is to be repaired or replaced.


PREPARATION FOR USE

  • Sizing / Adjustment

    For sizing information click here to refer to MCR Safety's sizing charts.

  • Recommended Storage Practices

    Do not store protective clothing in direct light. The strength of flame resistant fabrics can be degraded by exposure to light or fluorescent light and must be protected, either by storing in a shaded area or by covering with a dark material.


INSPECTION FREQUENCY & RETIREMENT CRITERIA

We recommend that each company establish its own criteria for regular, routine inspection and subsequent repair or retirement of protective clothing. Visual inspection for worn areas, mechanical damage, improper alterations, improper fit, or contamination with flammable substances may be cause for removal from service, as determined by the end user.


DONNING AND DOFFING PROCEDURES

For effective protection, flame-resistant garments should be worn as the outer garment with sleeves down and secured, shirts tucked into pants, and front closure fully secured.


PROPER USE CONSISTENT WITH NFPA 2113

For proper use information refer to NFPA 2113. The user is responsible to determine that this garment is appropriate for the intended use and complies with all laws and regulatory standards.
The user assumes all risks associated with the use of this product. MCR Safety shall not be liable for loss, injury, or death arising out of the use of this product.


MAINTENANCE AND CLEANING

  • Cleaning instructions and precautions

    Flammable contaminants adding during washing or drying will reduce the thermal protection properties of any flame-resistant garment. Properly caring for your FR clothing can help it continue to perform optimally and last longer.

    To ensure you know how to correctly wear, wash and maintain your garments, it is important to carefully follow instructions provided on the manufacturer’s care label. However, there are some basic care requirements that are applicable to all FR workwear:

    • Wash garments prior to wearing and after each subsequent wearing
    • Wash separately from standard clothing
    • Avoid using chlorine bleach
    • Thoroughly remove any oils and flammable contaminants from clothing
  • Maintenance criteria and methods of repair where applicable

    Ensure clothing is clean and in good repair before each wearing. Repair clothing using only FR fabric, thread and components. Return garments to manufacturer for repair or use an authorized repair facility.


RETIREMENT AND DISPOSAL

If the garment cannot be properly repaired or contaminants cannot be removed, the garment should be retired. The garment should be removed from service and retired after exposure to flame and heat.

Have Questions or Comments?

Need more information? Not finding what you need here? Tell us a little bit about you and we'll get right back to you to answer all your questions.

Ask us anything: Questions about our products and services, get information about an existing order, Make an order, Schedule an on-site assessment, Learn how to be a distributor, Find your closest distributor.

Just Try to Outwork Us!

By submitting this form I consent for MCR Safety to contact me for business and marketing purposes at the phone and/or email I provided via physical and/or automated methods. I understand I have the option to opt-out at any time. Visit www.mcrsafety.com/privacy for MCR Safety's privacy policy